Company News

seamless steel pipes

Company News

seamless steel pipes
Back to Results   |You are in :  Home  >  News  >  Company News

Classification of Quality Defects in Seamless Steel Pipes

Date:2026-11-10View:1810Tags:seamless steel pipes

1. Classification of Seamless Steel Pipe Quality Defects


Quality defects in seamless steel pipes fall into three main categories: surface defects, internal defects, and dimensional and shape defects. They differ in location, appearance and inspection requirements.


Surface defects: cracks, seams, scratches, folds and laps, scabs and scarring, pits.

Internal defects: internal cracks, non-metallic inclusions, porosity and looseness, segregation, shrinkage cavities and white spots.

Dimensional and shape defects: wall thickness variation, eccentricity, outside diameter deviation, ovality, straightness and length deviation.

seamless steel pipes


2. Surface Defects


Surface defects occur on the outside or inside surface of seamless steel pipes. Most are found by visual inspection; surface testing is added where the standard requires it.


2.1 Cracks, Seams and Scratches

Cracks: breaks in the metal, longitudinal or transverse, sometimes branching, with torn edges.

Seams: fine straight lines along the length, with smooth edges and no branching.

Scratches: narrow grooves from contact with tools or other pipes, running at any angle.


2.2 Folds, Scabs and Pits

Folds and laps: metal folded over and pressed into the surface, with a visible fold line.

Scabs and scarring: irregular patches of metal or oxide; when they come off they leave shallow depressions.

Pits: small depressions with rough bottoms, deeper than they are wide.


3. Internal Defects


Internal defects in seamless steel pipes sit inside the wall or open into the bore, so they cannot be seen from the outside. They are found by ultrasonic testing, sectioning or metallographic examination.


Internal cracks: breaks inside the wall, longitudinal or radial, that do not reach the outer surface.

Non-metallic inclusions: particles of oxide, sulphide or silicate trapped in the steel and elongated along the rolling direction. They appear as stringers or clusters in a section.

Porosity and looseness: scattered small voids, or local areas where the steel is not fully dense.

Segregation: a local concentration of alloying or impurity elements, usually along the centreline. It is a difference in composition, not a void.

Shrinkage cavities: irregular internal hollows, usually near the centre. They are larger and more open than porosity.

White spots: bright spots on a fracture surface that point to internal defects not visible from the outside.


4. Dimensional and Shape Defects


Dimensional defects in seamless steel pipes are measured values outside the specified tolerance. Shape defects are departures from the intended geometry, where the average size may still be correct.


4.1 Dimensional Defects

Wall thickness variation: the wall reads above or below the specified thickness at some point around the circumference or along the length.

Outside diameter deviation: the measured diameter sits outside the tolerance band, either over or under nominal.

Length deviation: the finished length differs from the ordered length beyond the permitted tolerance.


4.2 Shape Defects

Eccentricity: the bore and the outside diameter are not concentric, so one side of the wall is thick and the opposite side thin. The maximum and minimum wall sit on opposite sides of the section.

Ovality: the maximum and minimum diameter in the same cross-section differ, so the section is not round even when the average diameter is within tolerance.

Straightness deviation: the pipe axis departs from a straight line, measured as the maximum deflection over the specified length.


5. Defect Severity and Quality Acceptance


Acceptance depends on depth, length and the wall left after repair. Shallow scratches, scabs and pits can usually be ground out if the remaining wall stays above the minimum; cracks and seams generally cannot. The applicable standard and the purchase specification set the actual limits.


6. FAQs


Q1. What are the common quality defects in seamless steel pipes?

Surface defects include cracks, seams, scratches, folds and laps, scabs and scarring, and pits. Internal defects include inclusions, segregation and shrinkage cavities. Dimensional defects cover wall thickness, diameter, ovality and straightness.


Q2. How are defects in seamless steel pipes detected?

Visual inspection finds surface defects. Ultrasonic testing detects internal cracks and inclusions. Magnetic particle or dye penetrant testing is added where the standard requires it.


Q3. Can defects in seamless steel pipes be repaired?

Only where the standard allows it. Grinding is the usual repair for surface defects, and the remaining wall must stay above the minimum.


Related Articles

Seamless Steel Pipe Sizes

Hot Rolled Seamless Steel Pipe

Cold Drawn Seamless Steel Pipe: Process and Applications